Start with the cable LED on the dock’s USB-C cable. Dell says it stays off when the laptop’s USB-C port does not support video, data and power, so a dark LED means no screen will light. Then check the ports you used: the WD22TB4’s rear HDMI and MFDP USB-C video port are muxed, and Dell says only one of the two works at a time. Next, compare your monitors with Dell’s resolution table. A Thunderbolt laptop gets far more display bandwidth than a plain USB-C laptop. On a non-Thunderbolt laptop, two DisplayPort screens can drop to 1920 × 1080, and Dell says Intel graphics with the laptop screen on support only two displays. Update the laptop BIOS, graphics and Thunderbolt drivers, then the dock firmware. If screens still stay dark, Dell’s power reset is: unplug the USB-C cable, remove the dock’s power adapter, reconnect power first, then the laptop. NYBreaking did not test this dock.
Manufacturer documentation · Not physically tested by NYBreaking1. Read the cable LED and check power first
This page follows Dell’s WD22TB4 user guide and Dell Support articles, plus Microsoft’s multiple-monitor page. It is not a claim that NYBreaking tested a WD22TB4.
| What you see (Dell’s tables) | What Dell says it means or what to do |
|---|---|
| Cable LED on | The USB-C host “supports video + data + power”. |
| Cable LED off | The host “does not support video + data + power”. Make sure the dock has AC power, reconnect the cable and “make sure that the host port supports MFDP”. |
| No external display, no USB, cable LED off | “The docking connector has disconnected from the system’s USB/Thunderbolt ports.” Reconnect it; undock and reboot if that does not work. |
| Dock has no power | Disconnect USB-C from the laptop and unplug the dock’s adapter. Re-plug the adapter; the dock LED blinks 3 times. |
| Everything stopped after a power cut | Dell’s FAQ says the dock runs on AC power only and must renegotiate with the laptop. Disconnect and reconnect the AC adapter at the back of the dock. |
| “Undersized power adapter” warning | Check the dock’s own adapter. Laptops that need more than 130W must also use their own charger. |
Dell lists a 180W adapter for the WD22TB4, with 130W of power delivery to Dell laptops and 90W to non-Dell laptops. Its hardware note says the laptop needs a USB-C port with DisplayPort Alt Mode (supported) or a Thunderbolt port (recommended). Not sure what your port is? See how to check for a Thunderbolt or USB4 port.
2. HDMI and the MFDP USB-C port cannot both drive screens
- Dell’s video-connector page: “The HDMI and MFDP USB Type-C ports on the back of the WD22TB4 are muxed. Only one of these two ports can be used at a time.” If HDMI is in use, the USB-C port keeps its USB data function.
- So a setup with DP + DP + HDMI + a USB-C monitor on the MFDP port will show at most three of those screens. Move the fourth screen to one of the two rear Thunderbolt 4 ports, which Dell lists in its four-display combinations.
- On a non-Thunderbolt laptop, Dell says the two Thunderbolt ports “function as USB Type-C ports”.
| Screens (Dell list) | Port combinations Dell lists at 4K 60Hz |
|---|---|
| Two | DP 1.4 + HDMI 2.0 or MFDP · DP 1.4 + DP 1.4 · HDMI or MFDP + Thunderbolt · Thunderbolt + Thunderbolt |
| Three | DP 1.4 + DP 1.4 + HDMI 2.0 · DP 1.4 + DP 1.4 + MFDP |
| Four | DP 1.4 + DP 1.4 + HDMI 2.0 + Thunderbolt · DP 1.4 + DP 1.4 + MFDP + Thunderbolt |
The 4K 60Hz figures in that list depend on host bandwidth and DSC. Check section 3 for your laptop type.
3. Check Dell’s resolution table for your laptop
Dell publishes two tables: one for non-Thunderbolt (USB-C DisplayPort Alt Mode) laptops and one for Thunderbolt laptops. A few rows from each:
| Setup (Dell table) | Non-Thunderbolt laptop | Thunderbolt laptop |
|---|---|---|
| DP 1.4 + DP 1.4, HBR2 host | FHD (1920 × 1080) 60Hz each | QHD (2560 × 1440) 60Hz each |
| DP 1.4 + DP 1.4, HBR3 host | QHD 60Hz each | 4K 60Hz each |
| DP 1.4 + DP 1.4, HBR3 with DSC | 4K 60Hz each | 4K 60Hz each |
| DP + DP + HDMI, HBR3 without DSC | FHD 60Hz each | 1 × 4K 60Hz + 2 × QHD 60Hz |
| DP + DP + HDMI, HBR3 with DSC | QHD 60Hz each | 3 × 4K 60Hz |
- Intel graphics: Dell’s troubleshooting table says that with Intel graphics and the laptop screen in use, “only two displays can be supported”. With Nvidia or AMD discrete graphics, it lists three external displays plus the laptop screen.
- Monitor set above the dock’s limit: Dell says your monitor “may support higher resolutions than what the docking station is able to support”. Dell also notes the graphics driver may remove unsupported resolutions from Windows display settings, and that support depends on the monitor’s EDID.
- Linux: Dell says Linux cannot physically turn off the built-in display, so you get one external display fewer than the tables list.
- Laptop screen went dark: Dell notes the computer’s own video output may be disabled when a monitor is connected to the dock.
If a 4K screen runs at 30Hz instead, see 4K monitor stuck at 30Hz through a dock.
4. Update the laptop, then the dock firmware
Dell’s user guide recommends updating these on the laptop before using the dock:
- System BIOS
- Graphics driver
- Thunderbolt driver and Thunderbolt firmware (only on laptops that have Thunderbolt hardware)
- Ethernet driver
Dell’s caution: “Older BIOS versions and drivers could result in the docking station not being recognized by your system or not functioning optimally.” Keep the laptop on a charger while you update. Non-Dell laptops get these from their own maker’s support page.
Then update the dock. Dell says to download the WD22TB4 driver and firmware update from Dell Support, connect the dock, run the tool in administrative mode and click Update. The /componentsvers option shows the current version of every dock firmware component.
Screens gone after a Windows update? See Thunderbolt dock not working after a Windows update.
5. Approve the dock if Windows asks
- Dell’s FAQ says you are asked to approve a Thunderbolt device when the Thunderbolt security level in BIOS is set to “User Authorization” or “Secure Connect”.
- Dell lists the choices as “Always Connect”, “Connect Only Once” or “Do Not Connect”. Dell says you may choose Always Connect if you have no security concerns. If you picked Do Not Connect, reconnect the dock and choose again.
- On a work laptop, ask IT before changing BIOS security settings.
6. Daisy chains and screens that blank for a few seconds
- Daisy-chained pair shows one screen: Dell lists the WD22TB4 among docks where two daisy-chained monitors with MST turned on in the monitor menu cannot show video from the MFDP port. Dell says to connect the chain to the native DisplayPort 1.4 port instead. Dell notes DP 1.4 “supports MST mode on monitors with Display Stream Compression (DSC)” and MFDP does not.
- Four screens: in Dell’s Thunderbolt table, some four-screen rows need the fourth display to be “a 4K DSC monitor daisy chained through one of the monitors connected to the DP 1.4 port”.
- Screen goes black for 3 to 4 seconds: Dell says this “may be a result of Display Stream Compression (DSC) being enabled”, and that “updating the Dell Dock WD19 or Dell Thunderbolt Dock WD22TB4 to firmware version 01.00.36, 01.00.20 or later resolves the issue.” Also check cables, the graphics driver and the monitor’s own firmware. See monitor goes black for seconds through a dock.
7. Cables, inputs, Windows and isolation
- Power reset (Dell order): disconnect the USB-C cable, remove the dock’s power adapter, connect the power adapter first, then the USB-C cable to the laptop. Undock and reboot if that fails.
- Cable and input: disconnect both ends of the video cable, check for bent pins, reconnect firmly, and set the monitor to the matching input.
- Windows: Dell says to go to Display settings and under Multiple displays select the output for the second monitor, set to Extend. Microsoft’s guide also offers Detect under Settings → System → Display → Multiple displays, and Windows logo key + P.
- Flicker or distortion: Dell says to reset the monitor to factory defaults and reseat the cables. See also monitor flickering through a dock.
- Protected video: Dell says the dock supports HDCP up to 2.2, and the monitor must support HDCP 2.2 too.
- Isolate: Dell suggests trying a different monitor and cable known to be good.
For ports, power and Mac notes on this dock, see the Dell WD22TB4 profile. Using the older WD19 family? See Dell WD19 not detecting monitors.
Only Dell and Microsoft pages are sources. Forum threads and reviews are not cited. NYBreaking did not test a WD22TB4.
Sources you can inspect
- Dell: Dell Thunderbolt Dock WD22TB4 User Guide (PDF: hardware requirements, driver order, display resolution tables, power delivery, LED states, firmware update, FAQ) ↗
- Dell: WD22TB4 User Guide, Symptoms and solutions (no video, flicker, cable LED off, no dock power) ↗
- Dell: WD22TB4 User Guide, Video connectors for multiple display setup (HDMI and MFDP are muxed; 2, 3 and 4 display port combinations) ↗
- Dell Support: Monitor Experiences Intermittent Blanking when Connected to Dell Docking Stations (DSC, WD22TB4 firmware) ↗
- Dell Support: Daisy Chain Monitors Do Not Display Dual Video Through Dell Docking Stations with the MFDP Port ↗
- Microsoft Support: How to use multiple monitors in Windows (Windows logo key + P, Detect) ↗
Based on official documentation reviewed 2026-11-18. Steps are general; follow the manual for your exact model. No physical test by NYBreaking. Undocumented third-party dock behavior is not invented here. Published by Feroz Sheikh.
Put the conditions into your own setup.
Choose the exact equipment, then save or print the connection checklist.
Open the plannerFound a mismatch? Report a correction. No active paid affiliate links on this page.