First check the TS4’s LED. CalDigit says it shows white when the dock is powered and connected to your computer, and the TS4 needs its AC adapter to work at all. Make sure the cable runs from the Thunderbolt 4 port labelled “Computer”, using the supplied cable or a certified 40Gb/s Thunderbolt 4 / USB4 cable. Next, check the port the monitor uses. Only the DisplayPort 1.4 connector and the spare Thunderbolt 4 ports carry video. CalDigit says the three USB-C 10Gb/s ports are for data only. An HDMI screen on the DisplayPort needs an active adapter; CalDigit says a passive one will not work correctly. Then check your computer. CalDigit lists one external display for base M1 and M2 Macs and for Windows USB-C laptops, and two for Thunderbolt 3 and 4 PCs and many Macs. Last, update the TS4 firmware from CalDigit’s downloads page. NYBreaking did not test this dock.
Manufacturer documentation · Not physically tested by NYBreaking1. Check power, the LED and the host connection first
This page follows CalDigit’s TS4 user guide, product FAQ and downloads page, plus Apple’s and Microsoft’s display pages. It is not a claim that NYBreaking tested a TS4.
| What to check | What CalDigit says |
|---|---|
| Dock power | “The CalDigit TS4 requires power from the AC adapter to operate.” CalDigit also says to use only the power adapter supplied with the TS4 (230W in the box). |
| LED | The LED shows a white light “if the unit is powered on and connected to your computer”. No white light means start here, not with the monitor. |
| Host port on the dock | Connect from the Thunderbolt 4 port labelled “Computer” on the TS4 to a Thunderbolt 4, Thunderbolt 3 or USB-C port on the computer. |
| Cable | “Always use the supplied Thunderbolt 4 / USB4 cable or a certified 40Gb/s Thunderbolt 4 / USB4 cable.” CalDigit’s FAQ says 2m Thunderbolt 4 cables work without losing performance. |
| Computer port | CalDigit warns that some Windows PC makers limit what their USB-C and Thunderbolt 3 ports can do, including display output. Check the laptop maker’s specs for the port you use. |
Quick test: if a USB drive or keyboard on the TS4 works, the host link is up and the problem is on the video side. Do not use the Ethernet port as your test on a USB-C laptop: CalDigit says the TS4’s Ethernet works only on Thunderbolt hosts. Not sure what your port is? See how to check for a Thunderbolt or USB4 port.
2. Plug the monitor into a port that carries video
| TS4 port | Video? | CalDigit’s note |
|---|---|---|
| DisplayPort 1.4 (rear) | Yes | Only works with active adapters. “If you attempt to use a passive adapter, your display will not function correctly.” |
| Spare Thunderbolt 4 ports (2 downstream) | Yes | “Thunderbolt 4 Type-C supports video and data.” Use a USB-C or Thunderbolt monitor, or a USB-C video adapter. |
| USB-C 10Gb/s ports (3) | No | “These ports are intended for data use only.” |
| USB-A 10Gb/s ports (5) | No | Data and charging ports. |
- HDMI monitor: CalDigit’s two options are an active DisplayPort to HDMI adapter on the DisplayPort, or a USB-C to HDMI adapter on a spare Thunderbolt 4 port.
- Two monitors: CalDigit’s three layouts are DisplayPort plus one Thunderbolt 4 port, two Thunderbolt 4 ports with USB-C video adapters, or two USB-C/Thunderbolt monitors straight into two Thunderbolt 4 ports.
- Mac shows the wrong screen as main: the manual says a display on the DisplayPort “will be regarded as a secondary display by default”. Change it in Displays settings.
3. Check how many screens your computer can drive through the TS4
A dock cannot add display outputs your computer does not have. CalDigit’s FAQ gives this reference list and says to confirm with your computer maker:
| Computer (CalDigit FAQ) | External displays through the TS4 |
|---|---|
| Mac with M1 or M2 (base chip) | 1 |
| Mac with M1 Pro or M1 Max | 2 |
| Intel Mac with Thunderbolt 3 | 2 |
| Windows PC with Thunderbolt 4 | 2 |
| Windows PC with Thunderbolt 3 | 2 (CalDigit says some makers limit this to 1) |
| Windows PC with USB-C | 1 (depends on the USB-C port) |
| iPad (iPadOS) | 1 |
CalDigit’s product page adds newer Macs: M4 and M5 base chips, and Pro, Max and Ultra chips, can connect up to two displays. It says base M1, M2 and M3 Macs “do not support dual monitors through their Thunderbolt ports”, and that the M3 MacBook Air can run two external monitors with the lid closed. Apple’s rule is the same idea: the number of displays “depends on your Mac model”, so check your model’s specifications. For Mac-specific checks, see MacBook not detecting an external monitor and MacBook Air M4 with two monitors through a dock.
4. High resolutions and refresh rates need DSC and DP 1.4
- CalDigit: dual monitors above 4K 60Hz, such as two 5K or 6K screens, need monitors and a host GPU that support DSC 1.2 and DP 1.4 HBR3. A single screen above 4K 60Hz needs the same.
- CalDigit notes that the LG UltraFine 5K does not support DSC, and that some Thunderbolt 3 hosts with only DP 1.2 are capped at lower resolutions and refresh rates.
- The manual’s refresh-rate table lists 4K up to 144Hz and 2560 × 1440 up to 240Hz on Thunderbolt and USB4 hosts, but 3440 × 1440 only up to 100Hz on a 10Gb/s USB-C PC. CalDigit adds that “the support of higher refresh rates may vary due to OS updates”.
- Test step: if a high-refresh or 5K/6K screen stays dark, set it to 4K 60Hz or lower. The manual lists 4K 60Hz as supported on every host type in its table.
Stuck at 30Hz instead? See 4K monitor stuck at 30Hz through a dock.
5. Firmware, drivers and the operating system
- OS version: the manual lists macOS 11.4 or later and Windows 10 (20H2) or later.
- Dock firmware: CalDigit’s downloads page lists a TS4 Thunderbolt firmware updater and a USB PD firmware updater for macOS and Windows, with separate macOS update instructions. Follow those steps exactly.
- Windows drivers: CalDigit offers a Thunderbolt driver only “as a courtesy” and says to use it only if you cannot get the latest Thunderbolt software from your computer maker. Get graphics and Thunderbolt drivers from the laptop maker first.
- Windows: press Windows logo key + P, or use Detect in Display settings, as Microsoft describes. Mac: Apple says a powered, connected display is detected automatically; check System Settings > Displays.
- Isolate: connect the same monitor and cable straight to the computer. If it works there and not through the TS4, the dock path is the problem.
- Contact CalDigit: the manual asks for the TS4 serial number, OS version, and computer make and model.
For the dock’s ports and power, see the CalDigit TS4 profile. Deciding between models? See CalDigit TS4 vs TS5.
Only CalDigit, Apple and Microsoft pages are sources. Forum threads and reviews are not cited. NYBreaking did not test a TS4.
Sources you can inspect
- CalDigit: TS4 User Guide (PDF: powering and connecting the TS4, LED indicator, Thunderbolt 4 and USB-C port roles, DisplayPort and active adapters, single and dual monitor tables, specifications) ↗
- CalDigit: Thunderbolt Station 4 (TS4) product page and FAQ (dual monitors by Mac and PC type, DSC 1.2 and DP 1.4 HBR3 notes, HDMI options, cables) ↗
- CalDigit: Downloads (TS4 Thunderbolt firmware updater, USB PD firmware updater, Docking Station Utility, manuals) ↗
- Apple Support: Connect displays to your Mac (detection, number of displays by Mac model, display settings) ↗
- Microsoft Support: How to use multiple monitors in Windows (Windows logo key + P, Detect) ↗
Based on official documentation reviewed 2026-11-19. Steps are general; follow the manual for your exact model. No physical test by NYBreaking. Undocumented third-party dock behavior is not invented here. Published by Feroz Sheikh.
Put the conditions into your own setup.
Choose the exact equipment, then save or print the connection checklist.
Open the plannerFound a mismatch? Report a correction. No active paid affiliate links on this page.